What happens when you want a reliable solution for capturing footage in your vehicle? Well it’s important that you make informed decisions by investing in the best dash cam for your needs. However, installing said dash cam might not be as straightforward as you think, it requires some level of effort and perhaps a dash cam hardwire kit before you can finally get using your new bit of kit.
There are lots of things to consider with dash cam installation. For instance, the brand of your vehicle, the interior design, and your chosen dashcam brand are all important. Once you consider all these factors, you also need to ensure that you have the appropriate tools for completing the project. You also need to proceed with caution to avoid compromising the circuitry of your vehicle. Sounds complex right? We’ve written this post to simply and help you navigate the dash cam installation minefield.
How to Hardwire A Dash Cam
Choose the appropriate dashcam positioning
The first step is to sit in the driver’s seat position and try out various positions for the dashcam. A good recommendation is to ensure that the dashcam is installed close to the driver’s seat for optimal convenience. The camera should also be placed in such a way that it won’t compromise your vision of the road. More so, ensure the dash cam is placed at a position that provides the best footage for your needs.
Check the vehicle fusebox
Most dashcams are designed to acquire power from the power of the vehicle. For this reason, when carrying out the dash cam installation you will need to integrate the dash cam connections to that the of the vehicle.
The first step in this procedure is to locate the fuse box and connect the power supply to the camera. In most cases, the fuse box is often placed under the seats or in the engine section. If you don’t know where to find the fuse box or it’s perhaps damaged, then you might need to consult the manufacturer’s handbook.
Install the power cable
The next step is to install the power cable. To be specific, you will need to layout the power cable to power the functionalities of the camera. Ensure that you purchase a long cable and that the slack is sufficient enough as well. One of the important aspects of the dash cam installation is to tug on the rubber trim along the A-pillar to reveal a gap where the power cable will run.
In some cases, you might have to remove the entire A-pillar before attempting any dash cam installation procedures. Ensure that you use a wire that is durable and one that is well insulated. This is because a damaged wire might easily compromise the functionality of your dashcam.
Find the appropriate powering fuse
Step four of dash cam installation. Broadly speaking, while most vehicle fuses tend to have power running at all times, or perhaps when the vehicle is running alone, you need to choose the appropriate fuse. If you want the dash cam to start automatically when the engine is running and to turn off when the engine is off, you will need to add a special fuse that is referred to as the `hot in start` fuse.
You might have to use a special circuit test that helps to determine when power is flowing through the circuit. You will need to use a circuit tester to determine whether power is flowing through the vehicle when the ignition is off and on. Ensure that you remove the key from the ignition. You might need to use a fuse puller or perhaps a wrench to gently remove the fuse from the installation. For this part of the dash cam installation, you need to install the fuse that you have just removed.
Find a ground point
The other aspect of the dash cam installation, a wiring kit must be grounded in relation to your vehicle. In most cases, your vehicle should have a ground point that is close the fusebox for optimal user convenience. More so, depending on the unique design construction of your vehicle, you may have to introduce various unique modifications to achieve the best results.
Customise your installation
This step is meant to help you address any mistakes or flaws that may compromise the functionality of your dashcam. During this step of the process, ensure that you collect the excess power wire together. Following this, ensure that you safely secure the wiring to a solid mounting point, under the dashboard of the vehicle or perhaps behind the kick panel as used more zip ties.
Test the installation
The final step of dash cam installation is to test whether your installation works. Firstly, insert the key into the ignition and turn on the engine. If you installed all the components correctly, the dashcam should come on as soon as you start the vehicle. During this point, ensure that you place the interior panels correctly to facilitate the running power cable.
A good recommendation is to ensure that you test the installation as much as twice. In this way, you can determine whether the dashcam installation will provide long lasting results for your needs. You will also need to test whether the recorded footage is in the appropriate file format for your accessibility needs.
Dashcam Hardwire Kit
There are various components that you require to achieve the best installation results. These include:
l A pliers and insulation tape- the pliers will be used to pry open any challenging sections of the vehicle. More so, the insulation tape will be used to cover the tape for improved functionality
l Wire for the circuit- you need a long strand of wire which you will use to connect the dashboard to the fusebox
l A multimeter to test the flow of current- the multimeter is required to determine whether power can flow through the circuit
l A special fuse to control the functionality- you also need a circuit which will be used to ensure that the cam only starts when the vehicle is turned on.
l Superglue and installation clips- you also need superglue to seal any damaged spots and installation clips to ensure that you don’t leave any wires hanging.